How To Order


How To Order Air/Oil Tanks or Air Over Oil Cylinders

  1. Refer to Table No. 1, (Force Chart Extend) on page 16 to find effective area.
    (square inch) of cylinder.
  2. Multiple effective area by stroke of cylinder to determine volume.
  3. IMPORTANT: Multiply area by 1.5 safety factor.
  4. Select Air/Oil tank capacity closest to volume. See capacity chart below.
HOW TO ORDER DURA-TANK AIR/OIL TANK

Base your selection on a combination of space requirements, port size (for high speed) and cost.

Depending on space available, cost availability the customer could select DA2517T, DA3210T, DA4007T, DA5004T, DA6003T.


Unless otherwise specified all units are:

1) base mounted (precision block except models 07, 10, 40 & 50), 2) side ports, and 3) Sheave/Trolleys at position 1.


How To Order Powr-Tube Inflattable Bladders/Short Stroke Actuators

  • DUAL FITTINGS RECOMMENDED FOR MAXIMUM AIR FLOW

How To Order NFPA Full Duramount cylinders

HOW TO ORDER NFPA FULL DURAMOUNT CYLINDERS

NOTE: Model 15 (1.50" Bore) Not Available With Front Cushion or Front Bumper When Ordered With 1" Rod.

EXAMPLES:

DD 20 12 MS4 A 1 C DURAMASTER Cylinder, Double Rod, 2" Bore X 12" Stroke, Basic Cylinder MS4, 5/8" Rod Dia., Male Rod End 7/16-20, Both Cushions.

DS 32 18 MF1 C1 HR DURAMASTER Cylinder, Single Rod, 3 1/4" Bore X 18" Stroke, Front Flange Mount, 1 3/8" Rod, Dia., Male Rod End 1-14, Hydraulic, Rear Cushion.

NOTES:

  • *Model 15 requires stainless steel tie rods when ordered with magnetic piston and reed switches.
  • **Standard seal supplied when hydraulic, air/oil seal supplied when air over oil.
  • ***Decreases stroke by 1/16". Model 15 with 1" rod - not available with front bumper.

How To Order NFPA Duramount Cylinders

NOTE: Model 15 (1.50" Bore) Not Available With Front Cushion or Front Bumper When Ordered With 1" Rod.

EXAMPLES:

DPS 60 08 MS2 C2 CS DURAMASTER Cylinder with exposed nuts, Single Rod, 6" Bore X 8" Stroke, Side Lug Mount, 1 3/8" Rod Dia., Female Rod End 1-14, Both Cushions, Rod Scraper.

DPD 20 12 MS4 A 1 C DURAMASTER Cylinder with exposed nuts, Double Rod, 2" Bore X 12" Stroke, Basic Mount MS4, 5/8" Rod Dia., Male Rod End 7/16-20, Both Cushions. *Model 15 requires stainless steel tie rods when ordered with magnetic piston and reed switches.

NOTES:

  • Model 15 requires stainless steel tie rods when ordered with magnetic piston and reed switches.
  • Standard seal supplied when hydraulic, air/oil seals supplied when air over oil.
  • Decreases stroke by 1/16". Model 15 with 1" rod - not available with front bumper.
  • MF-2 or MS-7 Mounts are not available with “Duramount” Design. MP-1 & MP-2 not available on Model 15 or Model 20 “Duramount” Design.

HOW TO ORDER (DURAMITE II ROUND SERIES)

HOW TO ORDER (DURAMITE II ROUND SERIES)

EXAMPLES:

1-1/2" bore Single Rod with 12" stroke with MP-4 mounting and Low Friction: DRNS1512MP4A1L.

4" bore Double Rod with 6" stroke with MF-1 mounting, and Bumpers: DRND4006MF1B1B.

3-1/4" bore Single Rod with 4.25" stroke with MS-2 mounting, Female Rod End and Hydraulic: DRNS324.25MS2B2H.


HOW TO ORDER (DURA-E SERIES)

EXAMPLES:

1-1/2" bore, Single Rod with 12" stroke with MX-3 mounting: DES1512MX3A2.

4" bore Double Rod with 6" stroke with MF-1 mounting and Bumpers: DED4006MF1B2B.

3-1/4" bore Dura-Back-to-Back with 4.25" stroke on one end, and 2.75" stroke on other end with MS2 mounting and hydraulic: DEB324.25/2.75MS2B2H.

5" bore Dura-Power with 3 stages and 1" stroke with MX-2 mounting and magnetic piston: DE3P5001MX2B2M

2" bore Multi-Position with strokes in this order (starting with the rod retracted): 3.50", 6.25", 3.00" with MP-1 mounting: DE3M203.5/6.25/3.MP1A2.